Dewalt DCS370B 18V Cordless Band Saw User Manual

Home > Dewalt > Cordless Band Saw

Download Manual: DCS370.pdf

This manual, entitled DCS370, is 9,226,559 bytes (9.2 MB) and has mime type of application/pdf.

View Manual

DCS370

Heavy-Duty 18 Volt Cordless Band Saw

Scie à ruban industrielle sans fil de 18 volts

Sierra de banda para trabajo pesado, inalámbrica, de 18 voltios

INSTRUCTION MANUAL

GUIDE D’UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE

USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DEWALT • www.dewalt.com

1

English

Defi nitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to

these symbols.

DANGER: Indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation

which, if not avoided, may result in minor or moderate

injury.

NOTICE: Indicates a practice not related to personal injury

which, if not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR

ANY D

EWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT

(1-800-433-9258).

WARNING: To reduce the risk of injury, read the instruction

manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in

electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-operated

(corded) power tool or battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas

invite accidents.

b) Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Power tools create sparks which may ignite the dust or

fumes.

c) Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces

such as pipes, radiators, ranges and refrigerators. There

is an increased risk of electric shock if your body is earthed or

grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric

shock.

d) Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away

from heat, oil, sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension

cord suitable for outdoor use. Use of a cord suitable for

outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable,

use a ground fault circuit interrupter (GFCI) protected

supply. Use of a GFCI reduces the risk of electric shock.

2

English

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a power

tool while you are tired or under the influence of drugs,

alcohol or medication. A moment of inattention while

operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in

the off position before connecting to power source and/

or battery pack, picking up or carrying the tool. Carrying

power tools with your finger on the switch or energizing power

tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the

power tool on. A wrench or a key left attached to a rotating

part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry.

Keep your hair, clothing and gloves away from moving

parts. Loose clothes, jewelry or long hair can be caught in

moving parts.

g) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power tool

for your application. The correct power tool will do the job

better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do

not allow persons unfamiliar with the power tool or these

instructions to operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding

of moving parts, breakage of parts and any other condition

that may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to bind and

are easier to control.

g) Use the power tool, accessories and tool bits, etc. in

accordance with these instructions, taking into account

the working conditions and the work to be performed.

Use of the power tool for operations different from those

intended could result in a hazardous situation.

5) BATTERY TOOL USE AND CARE

a) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type of

3

English

battery pack may create a risk of fire when used with another

battery pack.

b) Use power tools only with specifically designated battery

packs. Use of any other battery packs may create a risk of

injury and fire.

c) When battery pack is not in use, keep it away from other

metal objects like paper clips, coins, keys, nails, screws,

or other small metal objects that can make a connection

from one terminal to another. Shorting the battery terminals

together may cause burns or a fire.

d) Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally occurs,

flush with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause

irritation or burns.

6) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Additional Safety Rules – Portable Band

Saws

• Hold power tool by insulated gripping surfaces when

performing an operation where the cutting accessory may

contact hidden wiring. Cutting accessories contacting a “live”

wire may make exposed metal parts of the power tool “live” and

could give the operator an electric shock.

• Keep hands away from cutting area and blade. Keep one

hand on the main handle and the other hand on the front handle to

prevent loss of control which could result in personal injury.

• Always make sure the portable band saw is clean before using.

• Always cease operation at once if you notice any abnormality

whatsoever.

• Always be sure all components are mounted properly and securely

before using tool.

• Always handle the band saw blade with care when mounting or

removing it.

• Always keep your hands out of the line of the band saw blade.

• Always wait until the motor has reached full speed before starting

a cut.

• Always keep handles dry, clean, and free of oil and grease. Hold the

tool firmly when in use.

• Always be alert at all times, especially during repetitive, monotonous

operations. Always be sure of position of your hands relative to the

blade.

• Never remove work stop.

• Stay clear of end pieces that may fall after cutting off. They may be

hot, sharp and/or heavy. Serious personal injury may result.

• Air vents often cover moving parts and should be avoided.

Loose clothes, jewelry or long hair can be caught in moving parts.

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are

NOT safety glasses. Also use face or dust mask if cutting operation is

dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities contains chemicals

known to the State of California to cause cancer, birth defects or

other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

4

English

......direct current ........alternating or direct

...........Class I Construction current

...............

(grounded)

n

o .........no-load speed

...........Class II Construction ..........earthing terminal

(double insulated)

..........safety alert symbol

…/min ....per minute BPM .....beats per minute

IPM .........impacts per RPM .....revolutions per

minute minute

ft/min ......feet per minute

Important Safety Instructions for All

Battery Packs

When ordering replacement battery packs, be sure to include catalog

number and voltage. Consult the chart at the end of this manual for

compatibility of chargers and battery packs.

The battery pack is not fully charged out of the carton. Before using

the battery pack and charger, read the safety instructions below. Then

follow charging procedures outlined.

READ ALL INSTRUCTIONS

• Do not charge or use battery in explosive atmospheres,

such as in the presence of flammable liquids, gases or dust.

Inserting or removing the battery from the charger may ignite the

dust or fumes.

• NEVER force battery pack into charger. DO NOT modify

battery pack in any way to fit into a non-compatible charger

as battery pack may rupture causing serious personal injury.

Consult the chart at the end of this manual for compatibility of

batteries and chargers.

• Charge the battery packs only in D

EWALT chargers.

• crystalline silica from bricks and cement and other masonry

products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed to

filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding,

sawing, grinding, drilling, and other construction activities.

Wear protective clothing and wash exposed areas with soap

and water. Allowing dust to get into your mouth, eyes, or lay on

the skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust,

which may cause serious and permanent respiratory or other

injury. Always use NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles away from face

and body.

WARNING: Always wear proper personal hearing protection

that conforms to ANSI S12.6 (S3.19) during use. Under some

conditions and duration of use, noise from this product may

contribute to hearing loss.

CAUTION: When not in use, place tool on its side on a stable

surface where it will not cause a tripping or falling hazard.

Some tools with large battery packs will stand upright on the battery

pack but may be easily knocked over.

• The label on your tool may include the following symbols. The

symbols and their definitions are as follows:

V ............. volts A ...........amperes

Hz ........... hertz W ..........watts

min .........minutes

........alternating current

5

English

• DO NOT splash or immerse in water or other liquids.

• Do not store or use the tool and battery pack in locations

where the temperature may reach or exceed 105°F (40°C)

(such as outside sheds or metal buildings in summer).

DANGER: Electrocution hazard. Never attempt to open the

battery pack for any reason. If battery pack case is cracked or

damaged, do not insert into charger. Do not crush, drop or damage

battery pack. Do not use a battery pack or charger that has received

a sharp blow, been dropped, run over or damaged in any way (i.e.,

pierced with a nail, hit with a hammer, stepped on). Damaged battery

packs should be returned to a service center for recycling.

NOTE: Battery storage and carrying caps are

provided for use whenever the battery is out of the

tool or charger. Remove cap before placing battery

in charger or tool.

WARNING: Fire hazard. Do not store or carry

battery so that metal objects can contact

exposed battery terminals. For example, do not place battery in

aprons, pockets, tool boxes, product kit boxes, drawers, etc., with

loose nails, screws, keys, etc. without battery cap. Transporting

batteries can possibly cause fires if the battery terminals

inadvertently come in contact with conductive materials such

as keys, coins, hand tools and the like. The U.S. Department

of Transportation Hazardous Material Regulations (HMR) actually

prohibit transporting batteries in commerce or on airplanes (i.e.,

packed in suitcases and carry-on luggage) UNLESS they are properly

protected from short circuits. So when transporting individual

batteries, make sure that the battery terminals are protected and

well insulated from materials that could contact them and cause a

short circuit.

SPECIFIC SAFETY INSTRUCTIONS FOR NICKEL CADMIUM

(NiCd) OR NICKEL METAL HYDRIDE (NiMH)

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

explode in a fire.

• A small leakage of liquid from the battery pack cells may

occur under extreme usage or temperature conditions. This

does not indicate a failure.

However, if the outer seal is broken:

a. and the battery liquid gets on your skin, immediately wash with

soap and water for several minutes.

b. and the battery liquid gets into your eyes, flush them with clean

water for a minimum of 10 minutes and seek immediate medical

attention. (Medical note: The liquid is 25–35% solution of

potassium hydroxide.)

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (Li-Ion)

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

explode in a fire. Toxic fumes and materials are created when

lithium ion battery packs are burned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If battery

liquid gets into the eye, rinse water over the open eye for 15

minutes or until irritation ceases. If medical attention is needed,

the battery electrolyte is composed of a mixture of liquid organic

carbonates and lithium salts.

• Contents of opened battery cells may cause respiratory

irritation. Provide fresh air. If symptoms persist, seek medical

attention.

WARNING: Burn hazard. Battery liquid may be flammable if

exposed to spark or flame.

6

English

The RBRC

TM

Seal

The RBRC™ (Rechargeable Battery Recycling

Corp oration) Seal on the nickel cadmium, nickel metal

hydride or lithium ion batteries (or battery packs)

indicate that the costs to recycle these batteries (or

battery packs) at the end of their useful life have already

been paid by D

EWALT. In some areas, it is illegal to place spent nickel

cadmium, nickel metal hydride or lithium ion batteries in the trash or

municipal solid waste stream and the RBRC program provides an

environmentally conscious alternative.

RBRC™ in cooperation with D

EWALT and other battery users, has

established programs in the United States and Canada to facilitate

the collection of spent nickel cadmium, nickel metal hydride or lithium

ion batteries. Help protect our environment and conserve natural

resources by returning the spent nickel cadmium, nickel metal hydride

or lithium ion batteries to an authorized D

EWALT service center or

to your local retailer for recycling. You may also contact your local

recycling center for information on where to drop off the spent battery.

RBRC™ is a registered trademark of the Rechargeable Battery

Recycling Corporation.

Important Safety Instructions for All

Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instructions for battery chargers.

• Before using charger, read all instructions and cautionary markings

on charger, battery pack, and product using battery pack.

DANGER: Electrocution hazard. 120 volts are present at charging

terminals. Do not probe with conductive objects. Electric shock or

electrocution may result.

WARNING: Shock hazard. Do not allow any liquid to get inside

charger. Electric shock may result.

CAUTION: Burn hazard. To reduce the risk of injury, charge only

D

EWALT rechargeable batteries. Other types of batteries may burst

causing personal injury and damage.

NOTICE: Under certain conditions, with the charger plugged in to

the power supply, the exposed charging contacts inside the charger

can be shorted by foreign material. Foreign materials of a conductive

nature such as, but not limited to, grinding dust, metal chips, steel

wool, aluminum foil, or any buildup of metallic particles should be

kept away from charger cavities. Always unplug the charger from

the power supply when there is no battery pack in the cavity. Unplug

charger before attempting to clean.

• DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual. The charger and

battery pack are specifically designed to work together.

• These chargers are not intended for any uses other than

charging D

EWALT rechargeable batteries. Any other uses may

result in risk of fire, electric shock or electrocution.

• Do not expose charger to rain or snow.

• Pull by plug rather than cord when disconnecting charger.

This will reduce risk of damage to electric plug and cord.

• Make sure that cord is located so that it will not be stepped

on, tripped over, or otherwise subjected to damage or

stress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk of

fire, electric shock, or electrocution.

• When operating a power tool outdoors, use an extension

cord suitable for outdoor use. Use of a cord suitable for outdoor

use reduces the risk of electric shock.

• An extension cord must have adequate wire size (AWG

or American Wire Gauge) for safety. The smaller the gauge

number of the wire, the greater the capacity of the cable, that is

7

English

16 gauge has more capacity than 18 gauge. An undersized cord

will cause a drop in line voltage resulting in loss of power and

overheating. When using more than one extension to make up the

total length, be sure each individual extension contains at least the

minimum wire size. The following table shows the correct size to

use depending on cord length and nameplate ampere rating. If in

doubt, use the next heavier gauge. The smaller the gauge number,

the heavier the cord.

Minimum Gauge for Cord Sets

Ampere Rating

Volts Total Length of Cord in Feet (meters)

120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

More

Than

Not

More

Than

AWG

0 6 18 16 16 14

610 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• Do not place any object on top of charger or place the

charger on a soft surface that might block the ventilation

slots and result in excessive internal heat. Place the charger

in a position away from any heat source. The charger is ventilated

through slots in the top and the bottom of the housing.

• Do not operate charger with damaged cord or plug.

• Do not operate charger if it has received a sharp blow, been

dropped, or otherwise damaged in any way. Take it to an

authorized service center.

• Do not disassemble charger; take it to an authorized service

center when service or repair is required. Incorrect reassembly

may result in a risk of electric shock, electrocution or fire.

• Disconnect the charger from the outlet before attempting

any cleaning. This will reduce the risk of electric shock.

Removing the battery pack will not reduce this risk.

• NEVER attempt to connect 2 chargers together.

• The charger is designed to operate on standard 120V

household electrical power. Do not attempt to use it on any

other voltage. This does not apply to the vehicular charger.

Using Automatic Tune-Up™ Mode

The automatic Tune-Up™ Mode equalizes or balances the

individual cells in the battery pack allowing it to function at peak

capacity. Battery packs should be tuned up weekly or after

10 charge/discharge cycles or whenever the pack no longer delivers

the same amount of work. To use the automatic Tune-Up™, place

the battery pack in the charger and leave it for at least 8 hours. The

charger will cycle through the following modes.

1. The red light will blink continuously indicating that the 1-hour

charge cycle has started.

2. When the 1-hour charge cycle is complete, the light will stay on

continuously and will no longer blink. This indicates that the pack

is fully charged and can be used at this time.

3. If the pack is left in the charger after the initial 1-hour charge, the

charger will begin the Automatic Tune-Up™ mode. This mode

continues up to 8 hours or until the individual cells in the battery

pack are equalized. The battery pack is ready for use and can be

removed at any time during the Automatic Tune-Up™ mode.

4. Once the Automatic Tune-Up™ mode is complete, the charger will

begin a maintenance charge; the red indicator will remain lit.

Chargers

Your tool uses a DEWALT charger. Be sure to read all safety instructions

before using your charger. Consult the chart on the back cover of this

manual for compatibility of chargers and battery packs.

8

English

FIG. 1

O

Charging Procedure (Fig. 1)

DANGER: Electrocution hazard. 120 volts are present at charging

terminals. Do not probe with conductive objects. Electric shock or

electrocution may result.

1. Plug the charger into an appropriate outlet before inserting battery

pack.

2. Insert the battery pack (O) into the charger, as shown in Figure 1,

making sure the pack is fully seated in charger. The red (charging)

light will blink continuously indicating that the charging process

has started.

3. The completion of charge will be indicated by the red light

remaining ON continuously. The pack is fully charged and may be

used at this time or left in the charger.

Indicator Light Operation

Charge Indicators

Some chargers are designed to detect certain problems that can arise

with battery packs. Problems are indicated by the red light flashing

at a fast rate. If this occurs, re-insert battery pack into the charger. If

the problem persists, try a different battery pack to determine if the

charger is OK. If the new pack charges correctly, then the original

pack is defective and should be returned to a service center or

other collection site for recycling. If the new battery pack elicits the

same trouble indication as the original, have the charger tested at an

authorized service center.

HOT/COLD PACK DELAY

Some chargers have a Hot/Cold Pack Delay feature: when the charger

detects a battery that is hot, it automatically starts a Hot Pack Delay,

suspending charging until the battery has cooled. After the battery

has cooled, the charger automatically switches to the Pack Charging

mode. This feature ensures maximum battery life. The red light flashes

long, then short while in the Hot Pack Delay mode.

PROBLEM POWER LINE

Some chargers have a Problem Power Line indicator. When the

charger is used with some portable power sources such as generators

or sources that convert DC to AC, the charger may temporarily

suspend operation, flashing the red light with two fast blinks

followed by a pause. This indicates the power source is out of limits.

LEAVING THE BATTERY PACK IN THE CHARGER

The charger and battery pack can be left connected with the red light

glowing indefinitely. The charger will keep the battery pack fresh and

fully charged.

NOTE: A battery pack will slowly lose its charge when kept out of

the charger. If the battery pack has not been kept on maintenance

9

English

4. The battery pack should be recharged when it fails to produce

sufficient power on jobs which were easily done previously. DO

NOT CONTINUE to use under these conditions. Follow the

charging procedure. You may also charge a partially used pack

whenever you desire with no adverse affect on the battery pack.

5. Under certain conditions, with the charger plugged into the power

supply, the exposed charging contacts inside the charger can

be shorted by foreign material. Foreign materials of a conductive

nature such as, but not limited to, grinding dust, metal chips, steel

wool, aluminum foil, or any buildup of metallic particles should

be kept away from charger cavities. Always unplug the charger

from the power supply when there is no battery pack in the cavity.

Unplug charger before attempting to clean.

6. Do not freeze or immerse charger in water or any other liquid.

WARNING: Shock hazard. Don’t allow any liquid to get inside

charger. Electric shock may result.

CAUTION: Never attempt to open the battery pack for any reason.

If the plastic housing of the battery pack breaks or cracks, return to

a service center for recycling.

Storage Recommendations

1. The best storage place is one that is cool and dry away from direct

sunlight and excess heat or cold.

2. Long storage will not harm the battery pack or charger. Under

proper conditions, they can be stored up to 3 years.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

charge, it may need to be recharged before use. A battery pack may

also slowly lose its charge if left in a charger that is not plugged into

an appropriate AC source.

WEAK BATTERY PACKS: Chargers can also detect a weak battery

pack. Such batteries are still usable but should not be expected to

perform as much work. The charger will indicate to replace battery

pack.

Important Charging Notes

1. Longest life and best performance can be obtained if the battery

pack is charged when the air temperature is between 65°F and

75°F (18° – 24°C). DO NOT charge the battery pack in an air

temperature below +40°F (+4.5°C), or above +105°F (+40.5°C).

This is important and will prevent serious damage to the battery

pack.

2. The charger and battery pack may become warm to touch while

charging. This is a normal condition, and does not indicate a

problem. To facilitate the cooling of the battery pack after use,

avoid placing the charger or battery pack in a warm environment

such as in a metal shed, or an uninsulated trailer.

3. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp or other

appliance;

b. Check to see if receptacle is connected to a light switch which

turns power off when you turn out the lights;

c. Move charger and battery pack to a location where the

surrounding air temperature is approximately 65°F – 75°F (18° –

24°C);

d. If charging problems persist, take the tool, battery pack and

charger to your local service center.

10

English

FIG. 2

A

D

C

BLADE DIRECTION

F2

F1

E

I

H

B

O

P

N

G

G

COMPONENTS (Fig. 2, 3)

WARNING: Never modify the power tool

or any part of it. Damage or personal injury

could result.

A. Auxiliary handle

B. Lock-off button

C. Trigger switch

D. Main handle

E. Work stop

F. Guide rollers

G. Adjusting lock nut

H. Blade tension lever

I. Blade

J. Hang hook

K. Pulley

L. Blade guard

M. Rubber tires

N. Tracking screws

O. Battery pack

P. Battery release buttons

INTENDED USE

This heavy-duty band saw is designed for

professional metal cutting applications.

DO NOT use under wet conditions or in

presence of flammable liquids or gases.

This band saw is a professional power tool.

DO NOT let children come into contact

with the tool. Supervision is required when

inexperienced operators use this tool.

11

English

Trigger Switch (Fig. 2)

Release switch lock-off button (B) by pressing

button. Pull the trigger switch (C) to turn

the motor ON. Releasing the trigger switch

turns the motor OFF. Releasing the trigger

switch also automatically actuates lock-

off button.

WARNING: This tool has no provision to

lock the switch in the ON position, and should

never be locked ON by any other means.

Blades

This portable band saw is setup for use with

.02" (0.5 mm) thick, 1/2" (12.5 mm) wide and

32" (813 mm) long blades. DO NOT use .025"

(.64 mm) thick blades.

WARNING: The use of any other blade or

accessory might be hazardous. DO NOT use

any other type of accessory with your band

saw. Blades used on stationary band saws

are of different thickness. Do not attempt to

use them on your portable unit.

Blade Selection

In general, first consider the size and shape of the work, and the type

of material to be cut. Remember, for the most efficient cutting, the

coarsest tooth blade possible should be used in a given application,

because the coarser the tooth, the faster the cut. In selecting the

appropriate number of teeth per inch of the band saw blade, at least

two teeth should contact the work surface when the blade is rested

against the workpiece. As a rule of thumb, soft materials usually require

coarse tooth blades, while hard materials require fine tooth blades.

P

A

E

J

FIG. 3

L

M

M

D

K K

Where a smoother finish is important, select one of the finer tooth

blades.

Select the appropriate band saw blade according to the material type,

dimensions, and number of teeth. See Blade Description chart.

The following table is intended as a general guide only. Determine the

type of material and dimension of the workpiece and select the most

appropriate band saw blade.

NOTICE: Never use the band saw to cut resin materials which are

subject to melting. Melting of resin material caused by high heat

12

English

generated during cutting may cause the band saw blade to become

bound to the material, possibly resulting in overload and burn-out of

the motor.

BLADE DESCRIPTION

Type of band saw blade Bi-Metal

Number of teeth 24 18 14 14/18

Workpiece thickness

1/8" (3.2mm) and under • •

1/8"–1/4" (3.2mm–6.4mm) • •

Blade Tracking (Fig. 2)

WARNING: To reduce the risk of serious personal injury, turn

tool off and remove battery pack before making any adjustments

or removing/installing attachments or accessories. An accidental

start-up can cause injury.

NOTICE: Excessive tightening of the adjustment screws could result

in damage to the saw.

Your band saw is equipped with an adjustable blade tracking

mechanism which assures proper blade tracking at all times. The

blade is properly adjusted when it is centered on the guide rollers (F)

and the teeth of the blade (I) are 3/16" (0.38 mm) from the edge of

the guide roller.

TO ADJUST THE BLADE TRACKING

1. Turn and open the blade tensioning lever (H) to allow access to the

tracking screws (N).

2. Use a 10mm wrench to loosen the adjustment locking nuts (G).

3. Use a 3 mm hex wrench (supplied) to turn one of the tracking

screws (N) 1/4 turn clockwise. Turn the other tracking screw 1/4

turn clockwise.

NOTE: Turning the tracking screw clockwise moves the blade

toward the guide roller, turning the tracking screw counterclockwise

moves the blade away from the guide roller.

4. Tighten both the adjusting locking nuts and close the quick release

lever. (It will be necessary to run the saw to observe the tracking.)

5. Observe blade tracking between runs and repeat Steps 1–4 as

necessary to achieve proper blade tracking.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal injury, turn

tool off and remove battery pack before making any adjustments

or removing/installing attachments or accessories. An accidental

start-up can cause injury.

FIG. 4

P

Installing and Removing the Battery Pack

(Fig. 1, 2, 4)

NOTE: Make sure your battery pack is fully charged.

WARNING: Make certain the switch lock-off button (B)

is engaged to prevent switch actuation before removing or

installing battery.

To install the battery pack into the tool handle, align the base of

the tool with the notch inside the tool’s handle and slide the battery

pack firmly into the handle until you hear the lock snap into place.